| Command |
Purpose |
| alternator_torq |
Perform real-time calculations of alternator loss, shaft power, and shaft torque based on input data from a specification file and observed speed and power values. Engine net torque, power and alternator loss will be output at the interval specified as a command line argument when the task is started. |
| blk_num_mgr.10c |
This application is not intended for users to execute on the command line interface. Manages block number assignments by responding to requests from other applications, incrementing and saving values to a specified file, and operating as an event-driven service. |
| blk_num_mgr.12 |
Perform the Analog Input Transfer Task. |
| bp |
Capture CVS test cell errors when a problem occurs. |
| ci_logr_spec.b09 |
Generate a logr_spec output file by copying contents from an input file and appending a @SCAN_LIST section based on data from a ci_specs file. |
| ci2fur |
Read a customer interface specification file and generate a test_map file based on its contents for use by other applications. |
| CVS_O2_data |
Read an input file that was generated on the Modcomp computer and read the oxygen concentration and the time that the concentration was last updated. |
| esvd_pre_star5.12 |
Write information to the floger data file that will contain the test cycle data. The information is data that is needed by the programs that process the logged data at the conclusion of the test. |
| esvd_pre_star5.b09 |
Write information to the data file that will contain the test cycle data, including details needed for processing logged data at the end of the test. |
| esvd_star5.12 |
Create the star5 section of raw_data_file (star file) for esvd programs. |
| esvd_star5.b09 |
Generate the star5 section of the raw data file for ESVD programs by processing floger data, emission bench data, and other inputs to compute and output emission-related statistics and values. |
| filterdata.10c |
Gather data from spec files and creates a keyword file |
| filterdata.12 |
Gather data from spec files and creates a keyword file. |
| filterdata12.raw |
Gather data from spec files and create a keyword file. |
| filterdata.raw |
Gather data from spec files and create a keyword file |
| get_cvs_version |
Determine the version level of the cvs_specs file . |
| get_site_cfg12 |
Get the @SITE_CONFIG entry in the cvs_specs file |
| mk_config_files12 |
Create the cell_map and test_map files from data within the tri_specs.dat file. |
| mk_ecm_files |
Generate configuration files including asam3_specs and ecm_override from input data. |
| mk_ecm_files12 |
Generate the asam3_specs file and ecm_override files from data in the tri_specs file based on provided parameters. |
| mk_map_files |
Create the cycle_map file from data within the cvs_specs file. |
| release_burn_emis |
Set the event to release a specified burn_emis task instance, allowing it to clean up and exit. |
| run_num_mgr.10c |
Manage and assign run numbers for CyFlex applications, incrementing based on hot or cold cycles and requesting new blocks when necessary. |
| run_num_mgr.12 |
Execute the run number manager. |
| star1.12 |
The star1 task creates the star1 file. |
| star1.b09 |
Create the star1 file using data from specified input files. |
| star2_7.12 |
Create the star2 and star7 files. |
| star2_7.b09 |
Purpose: Create the star2 and star7 files based on specified input files. |
| star_pream.12 |
Create the star preamble file for the esvd programs. |
| star_pream.b09 |
Create the star preamble file for the esvd programs. |
| tca.10c |
Perform Torque Curve Analysis for file format 10. |
| tca.12 |
Perform Torque Curve Analysis for file format 12. |
| tca_header.10c |
Generate a header section for a loger data file used in torque curve analysis, create the loger specification file based on customer input, and set necessary variables for the CyFlex system. |
| tca_logr.12 |
Create the loger specification file and write it to disk. |
| tpa_extract_data |
Perform Three Pressure Analysis (TPA) Extract Data task. |
| tpa_ss_data |
Perform initialization required by the TPA task. |
| write_ecm_overrides12 |
Generate the ecm_ovrd file from data in the tri_specs file based on the specified testid, activity, ECM string variable, and ECM variable value. |
| write_ecm_specs12 |
Generate the ASAM3 specifications file from data in the TRI specifications file. |